Getta Grip

I’ve worked with other tube lights and their cases are so heavy and only come when you buy 4 or 8 quantities ($$$$). Plus I was tired of hauling them individually so I decided to make a case. It’s still a prototype but way more efficient, lighter, and safer to transport!

I had these extra silks and nets for a 18x24 kit but not enough frames so instead buying the frames, I decided to make some instead! I can confidently say that welding is a delicate art form. Enjoy!

Definitely batting a 1000 on this one! What you will need for this build:

(1) 6” Matthellini clamp
(1) 2.5” Matthews grip head
(1) 3/8” hex nut
(1) 3/8” modern studio male baby pin
(1) ball head with 3/8” female receiver

Gettagrip: Hotel edition part 3! Thank you to for the lens and support! What you will need for this build:

(1) 3ft 5/8” rod
(2) 2ft 5/8” rod
(3) small rig super clamps
(3) 9. Solutions closed 5/8” gag
(1) 9. Solutions open gag 5/8” gag
(1) 9. Solutions dual 5/8” gag
(3) 3/8” male baby pin
(1) 3/8” female threaded ball head
(1) 2 inch 1/4” baby pin starter
(1) 5/8” receiver with 3/8” male thread
(1) 3/16” speed wrench

GettaGrip: Hotel edition part 2! What you will need for this build:

(2) 6” matthellini clamp
(1) 3” matthellini clamp
(2) 2.5” grip heads
(2) 9. Solutions closed 5/8” gag
(1) 9. Solutions open gag 5/8” gag
(1) 9. Solutions dual 5/8”
(2) 3ft 5/8” rod
(1) 2ft 5/8” rod
(1) 18 inch 5/8” rod
(1) 1ft. 5/8” rod
(1) 2 inch 1/4” baby pin starter
(1) 3/8” female threaded ball head
(1) Modern Studio 5/8” fixed cross
(1) Gripfilm 5/8” swivel cross
(1) 3/16” speed wrench

What’ll need for this build:

(3) 36” 5/8” rods
(1) 3/16” speed wrench
(1) 9. Solutions mini python clamp
(2) 9. Solutions 5/8” closed gag
(1) 9. Solutions 5/8” open gag
(1) 1/4-20 male baby pin
(1) gripfilm 5/8” swivel cross
(3) 6” end jaw matthellinis
(1) ball head with 3/8” female thread

Was a bit uneasy without top safety for this but with a lightweight camera, the guidelines can be bent to accommodate. What you’ll need for this build:

(3) 36” 5/8” rods
(1) 24” 5/8” rod
(1) 18” 5/8” rod
(1) 16” 5/8” rod
(1) 5/8” receiver with 3/8” male thread
(3) 6” end jaw matthellinis
(2) 5/8” fixed crosses
(1) 2” 1/4-20 male baby pin
(1) ball head with 3/8” female thread
(3) 9. Solutions mini python clamp
(1) 9. Solutions 5/8” open gag
(3) 9. Solutions 5/8” closed gag
(1) 3/16” speed wrench

Shortly into this build, I didn’t have 5/8” rods long enough, so speed rail it was! What you’ll need for this build:

(2) 6ft. Speed rail (1.5”)
(1) 3ft. speed rail (1.5”)
(2) 2ft. speed rail (1.5”)
(4) 1.5” swivel cheeseboros
(4) 1.5” short barrel crosses
(1) half pro-burger clamp
(1) 3/8” female thread ball head
(1) 3/16” speed wrench
(2) 1.5” swivel T’s
(4) 3/8” bolts with washers
(4) 3.5” speed rail starters (1.5”)
(1) 9/16” wrench

camerarigging

Gear needed for this build:

(3) 36” 5/8” rods
(4) 3” end jaw matthellinis
(3) 9. Solutions mini python clamp with 5/8” receiver
(2) 9. Solutions closed 5/8” gag
(2) 5/8” fixed crosses
(2) gripfilm 5/8” swivel crosses
(2) 18” 5/8” rods
(1) 14” 5/8” rod
(1) 2” baby pin (1/4-20 male thread)
(1) k&f concept ball head with 3/8” female receiver
(1) 3/16” speed wrench

This build is on a roll! What you will need:

(2) 6” end jaw matthellini clamps
(1) 3/16” speed wrench
(2) Gripfilm 5/8” swivel cross
(1) 2 inch 1/4” baby pin starter
(1) 3/8” female threaded ball head
(1) 5/8” receiver with 3/8” male thread
(2) 9. Solutions closed 5/8” gag
(2) 2ft 5/8” rod
(1) 10 inch 5/8” rod
(1) 9. Solutions 5/8” mini python clamp

Thought this would be more complicated but was much simpler than thought. What you will need for this build:

(2) 6” End Jaw Matthellini clamps
(1) 3/16” speed wrench
(1) 9. Solutions 5/8” mini python clamp
(1) Gripfilm 5/8” swivel cross
(1) 3/8” female threaded ball head
(2) Modern Studio 5/8” fixed cross
(1) 9. Solutions closed 5/8” gag
(1) 2 inch 1/4” baby pin starter
(1) 3/8” male baby pin with (1) 3/8” hex nut
(1) 18 inch 5/8” rod
(1) 3ft 5/8” rod