Secret Computer and Phone Repair Services

The description and instructions written on the box of iS-006 Double-Headed Repair Data Cable

(The iS-006 Repair Data Cable is used to put an iPhone into Recovery Mode without manual buttons.)

iS-006 Double-Headed Repair Data Cable (by iSoft)

This is used to put an iPhone into Recovery Mode without manual buttons.

Conductive Silver Paste

This is used to repair broken circuits and create electrical connections without soldering. The paste has silver particles that conduct electricity.

This is a good alternative to soldering for heat sensitive parts and is usually used in repairs of devices and parts with broken PCB traces or pads like the display (e.g. LCD screens), keyboards, remote controls, and membrane switches.

NOTE: This is not recommended for high-voltage applications. Also, silver paste is mostly used for trace repair and pad reconstruction but is not recommended for replacing normal solder joints.

150°C Solder Paste (YCS Brand)

Solder Paste is used to to solder surface mount components onto printed circuit boards (PCBs).

This is a 150°C solder paste which means that its melting point is 150° celsius.

Solder paste comes in varying melting points including 138°C, 158°C, 183°C, 199°C, and 217c.

Restocking our 2mm Edge Screen Frame Double-Sided Tape

A close-up on RL-007GA (the dot repair soldering lugs by Relife)

If you are tired rolling jumper wires or flying wires into broken solder pads, you may try these dot repair sodlering lugs instead. No need to roll tiny wires into flat circles; just place a dot repair solder lug on the broken solder pad and its line and you are now ready for soldering.

Relife RL-007GA features rounded solder lugs which is suitable for phone motherboards.

Dot Repair Soldering Lugs by Relife:
RL-007GA

If you are tired rolling jumper wires or flying wires into broken solder pads, you may try these dot repair sodlering lugs instead. No need to roll tiny wires into flat circles; just place a dot repair solder lug on the broken solder pad and its line and you are now ready for soldering.

Relife RL-007GA features rounded solder lugs which is suitable for phone motherboards.

A close-up on a patch of Dot Repair Soldering Lugs

If you are tired rolling jumper wires or flying wires into broken solder pads, you may try these dot repair sodlering lugs instead. No need to roll tiny wires into flat circles; just place a dot repair solder lug on the broken solder pad and its line and you are now ready for soldering.

Dot Repair Soldering Lugs

If you are tired rolling jumper wires or flying wires into broken solder pads, you may try these dot repair sodlering lugs instead. No need to roll tiny wires into flat circles; just place a dot repair solder lug on the broken solder pad and its line and you are now ready for soldering.

Dock Flex Tester - Lightning

This is used to quickly check the functionality of the charging port, the U2 IC (or the charging chip), and the battery without disassembling the phone.

By plugging this into the charging port, it allows technicians to measure pin voltage and continuity using a multimeter; thus, identifying faults like broken traces or charging issues.

This diagnostic tool typically involves plugging this tester into the phone's charging port to check the pins (using a multimeter in diode mode). This usually measures the VBUS (5V), the USB data lines (DP/DM), and the identification pins to determine if the charger, the port, or internal components are failing.

This tool usually comes in microUSB, Type-C, and Lightning port variants.

Dock Flex Tester - Type-C

This is used to quickly check the functionality of the charging port, the U2 IC (or the charging chip), and the battery without disassembling the phone.

By plugging this into the charging port, it allows technicians to measure pin voltage and continuity using a multimeter; thus, identifying faults like broken traces or charging issues.

This diagnostic tool typically involves plugging this tester into the phone's charging port to check the pins (using a multimeter in diode mode). This usually measures the VBUS (5V), the USB data lines (DP/DM), and the identification pins to determine if the charger, the port, or internal components are failing.

This tool usually comes in microUSB, Type-C, and Lightning port variants.

Dock Flex Tester - MicroUSB

This is used to quickly check the functionality of the charging port, the U2 IC (or the charging chip), and the battery without disassembling the phone.

By plugging this into the charging port, it allows technicians to measure pin voltage and continuity using a multimeter; thus, identifying faults like broken traces or charging issues.

This diagnostic tool typically involves plugging this tester into the phone's charging port to check the pins (using a multimeter in diode mode). This usually measures the VBUS (5V), the USB data lines (DP/DM), and the identification pins to determine if the charger, the port, or internal components are failing.

This tool usually comes in microUSB, Type-C, and Lightning port variants.